View SA07_4525205.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

rom P r o d u c t IIn n o vva t i o n FF r o m nno a
SA07 SA07
DESCRIPTION
The SA07 amplifier is a 40 volt, 500kHz PWM amplifier. The full bridge output circuit provides 5 amps of continuous drive current for applications as diverse as high fidelity audio and brush type motors. Clock output and input pins can be used for synchronization with other amplifiers or an externally generated clock. An integrator amplifier is provided. Direct access to the pwm input is provided for connection to digital motion control circuits. Protection circuits guard against thermal overloads as well as shorts to supply or ground. The current limit is programmable with one or two external resistors depending on the application. A shutdown input disables all output bridge drivers. The 18 pin steel package is hermetically sealed.
Pulse Width Modulation Amplifiers
FEATURES
500kHzSWITCHING FULLBRIDGEOUTPUT5-40V(80VP-P) 5AOUTPUT 1IN2FOOTPRINT FAULTPROTECTION SHUTDOWNCONTROL SYNCHRONIZABLECLOCK HERMETICPACKAGE
APPLICATIONS
HIGHFIDELITYAUDIOAMPLIFIER BRUSHTYPEMOTORCONTROL VIBRATIONCANCELLINGAMPLIFIER
BLOCK DIAGRAM AND TYPICAL APPLICATION CONNECTIONS HIGH FIDELITY AUDIO
SA07U
http://www.cirrus.com
Copyright (c) Cirrus Logic, Inc. 2008
(All Rights Reserved)
AUG2008 APEX - SA07REVD
SA07
EXTERNALCONNECTIONS
P r o d u c t I n n o v a t i o nF r o m
18-pin DIP PACKAGE STYLE EL
Case tied to Pin 7. Allow no current in case. Bypassing of supplies is required. If +PWM > RAMP then A OUT > B OUT.
1. CHARACTERISTICS AND SPECIFICATIONS ABSOLUTE MAXIMUM RATINGS
Parameter SUPPLY VOLTAGE, +Vs to GND, 10mS surge SUPPLY VOLTAGE, +VCC to GND OUTPUT CURRENT, peak POWER DISSIPATION, internal TEMPERATURE, pin solder, 10s TEMPERATURE, junction TEMPERATURE, storage OPERATING TEMPERATURE RANGE, case INPUTS (Note 1) -65 -55 -0.4 (Note 3) Symbol Min Max 60 16 7.5 80 300 150 150 125 +5.4 Units V V A W C C C C V
CAUTION
The SA07 is constructed from MOSFET transistors. ESD handling procedures must be observed. The internal substrate contains beryllia (BeO). Do not break the seal. If accidentally broken, do not crush, machine, or subject to temperatures in excess of 850C to avoid generating toxic fumes.
2

SA07U
P r o d u c t I n n o v a t i o nF r o m
SA07
SPECIFICATIONS
Parameter ERROR AMP, CLOCK REF OFFSETVOLTAGE BIASCURRENT OFFSETCURRENT COMMONMODEVOLTAGERANGE COMMON MODE REJECTION, DC SLEWRATE OPENLOOPGAIN GAINBANDWIDTHPRODUCT CLOCKOUT CLOCK OUT, high level CLOCK OUT, low level 5VOUT OUTPUT EFFICIENCY, 5A output SWITCHINGFREQUENCY CURRENT, continuous CURRENT, peak RDS(ON) POWER SUPPLY VOLTAGE, VCC VOLTAGE, VS CURRENT, VCC CURRENT, VS INPUTS ILIM/SHDN, trip point -PWM, +PWM, low level -PWM, +PWM, high level CLOCK IN, low level CLOCK IN, high level THERMAL RESISTANCE, junction to case RESISTANCE, junction to air TEMPERATURE RANGE, case (Note 2) Full temperature range Full temperature range Meets full range specifications -25 15 85 3.5 C/W C/W C (Note 4) 90 0 2.7 0 3 110 0.8 VCC 0.3 5.6 mV V V V V Full temperature range Full temperature range Switching Switching, no load 10 5 12 16 40 50 90 V V mA mA (Note 4) (Note 4) 100 ms, 10% duty cycle 5 7 0.55 VS=40V 94 500 % kHz A A LOAD 5mA 0.98 4.7 0 4.988 5 0 70 12 100 10 1 1.02 5.3 0.2 5.012 (Note 1) (Note 4) 10 50 30 3 mV pA pA V dB V/S dB MHz MHz V V V Test Conditions Min Typ Max Units
NOTES:
1. All Min/Max characteristics and specifications are guaranteed over the Specified Operating Conditions. Typical performance characteristics and specifications are derived from measurements taken at typical supply voltages and TC = 25C. 2. Long term operation at the maximum junction temperature will result in reduced product life. Derate internal power dissipation to achieve high MTTF. For guidance, refer to the heatsink datasheet. 3. 40W in each of the two active output transistors on at any one time. 4. Min max values guaranteed but not tested.

SA07U
SA07
P r o d u c t I n n o v a t i o nF r o m

SA07U
P r o d u c t I n n o v a t i o nF r o m
SA07
GENERAL
Please read Application Note 30 on "PWM Basics". Refer to Application Note 1 "General Operating Considerations" for helpful information regarding power supplies, heat sinking and mounting. Visit www.apexmicrotech. com for design tools that help automate pwm filter design and heat sink selection. The "Application Notes" and "Technical Seminar" sections contain a wealth of information on specific types of applications. Information on package outlines, heat sinks, mounting hardware and other accessories are located in the "Packages and Accessories" section. Evaluation Kits are available for most Apex product models, consult the "Evaluation Kit" section for details. For the most current version of all Apex product data sheets, visit www.apexmicrotech.com. The clock frequency is internally set to a frequency of approximately 1MHz. The CLK OUT pin will normally be tied to the CLK IN pin. The clock is divided by two and applied to an RC network which produces a ramp signal at the RAMP pin. An external clock signal can be applied to the CLK IN pin for synchronization purposes. If a clock frequency lower than 1MHz is chosen an external capacitor must be tied to the RAMP pin. This capacitor, which parallels an internal capacitor, must be selected so that the ramp oscillates 2.5 volts p-p with the lower peak 1.25 volts above ground.
CLOCK CIRCUIT AND RAMP GENERATOR
BYPASSING
Adequate bypassing of the power supplies is required for proper operation. Failure to do so can cause erratic and low efficiency operation as well as excessive ringing at the outputs. The Vs supply should be bypassed with at least a 1F ceramic capacitor in parallel with another low ESR capacitor of at least 10F per amp of output current. Capacitor types rated for switching applications are the only types that should be considered. The bypass capacitors must be physically connected directly to the power supply pins. Even one inch of lead length will cause excessive ringing at the outputs. This is due to the very fast switching times and the inductance of the lead connection. The bypassing requirements of the VCC supply are less stringent, but still necessary. A 0.1F to 0.47F ceramic capacitor connected directly to the VCC pin will suffice.
NOISEFILTERING
Switching noise can enter the SA07 through the INT OUT to +PWM connection. A wise precaution is to low pass filter this connection. Adjust the pass band of the filter to 10 times the bandwidth required by the application. Keep the resistor value to 100 ohms or less since this resistor becomes part of the hysteresis circuit on the pwm comparator.
PCB LAYOUT
The designer needs to appreciate that the SA07 combines in one circuit both high speed high power switching and low level analog signals. Certain layout rules of thumb must be considered when a circuit board layout is designed using the SA07: 1. Bypassing of the power supplies is critical. Capacitors must be connected directly to the power supply pins with very short lead lengths (well under 1 inch). Ceramic chip capacitors are best. 2. Make all ground connections with a star pattern at pin 7. 3. Beware of capacitive coupling between output connections and signal inputs through the parasitic capacitance between layers in multilayer PCB designs. 4. Do not run small signal traces between the pins of the output section (pins 11-16). 5. Do not allow high currents to flow into the ground plane. 6. Separate switching and analog grounds and connect the two only at pin 7 as part of the star pattern.
SA07U

SA07
INTEGRATOR
P r o d u c t I n n o v a t i o nF r o m
The integrator provides the inverted signal for negative feedback and also the open loop gain for the overall application circuit accuracy. Recommended value of CINT is 10 pF for stability. However, poles and zeroes can be added to the circuit for overall loop stability as required.
CURRENT LIMIT
There are two load current sensing pins, I SENSE A and I SENSE B. The two pins can be shorted in the voltage mode connection but both must be used in the current mode connection (see figures A and B). It is recommended that RLIMIT resistors be non-inductive. Load current flows in the I SENSE pins. To avoid errors due to lead lengths connect the I LIMIT/SHDN pin directly to the RLIMIT resistors (through the filter network and shutdown divider resistor) and connect the RLIMIT resistors directly to the GND pin. Do not connect RLIMITsense resistors to the ground plane.
Switching noise spikes will invariably be found at the I SENSE pins. The noise spikes could trip the current limit threshold which is only 100 mV. RFILTER and CFILTER should be adjusted so as to reduce the switching noise well below 100 mV to prevent false current limiting. The sum of the DC level plus the noise peak will determine the current limiting value. As in most switching circuits it may be difficult to determine the true noise amplitude without careful attention to grounding of the oscilloscope probe. Use the shortest possible ground lead for the probe and connect exactly at the GND terminal of the amplifier. Suggested starting values are CFILTER = 0.001uF, RFILTER = 5k .
0
The required value of RLIMIT in voltage mode may be calculated by: RLIMIT = 0.1 V / ILIMIT where RLIMIT is the required resistor value, and ILIMIT is the maximum desired current. In current mode the required value of each RLIMIT is 2 times this value since the sense voltage is divided down by 2 (see Figure B). If RSHDN is used it will further divide down the sense voltage. The shutdown divider network will also have an effect on the filtering circuit.
SHUTDOWN
The shutdown circuitry makes use of the internal current limiting circuitry. The two functions may be externally combined in voltage and current modes as shown below in Figures A and B. The RLIMIT resistors will normally be very low values and can be considered zero for this application. In Figure A, RSHDN and 1K form a voltage divider for the shutdown signal. After a suitable noise filter is designed for the current limit, adjust the value of RSHDN to give a minimum 110 mV of shutdown signal at the I LIMIT/SHDN pin when the shutdown signal is high. Note that CFILTER will filter both the current limit noise spikes and the shutdown signal. Shutdown and current limit operate on each cycle of the internal switching rate. As long as the shutdown signal is high the output will be disabled.

SA07U
P r o d u c t I n n o v a t i o nF r o m
SA07
PROTECTIONCIRCUITS
Circuits monitor the temperature and load on each of the bridge output transistors. On each cycle should any fault condition be detected all output transistors in the bridge are shut off. Faults protected against are: shorts across the outputs, shorts to ground, and over temperature conditions. Should any of these faults be detected, the output transistors will be latched off *. In addition there is a built in dead time during which all the output transistors are off. The dead time removes the possibility of a momentary conduction path through the upper and lower transistors of each half bridge during the switching interval. Noise or flyback may be observed at the outputs during this time due to the high impedance of the outputs in the off state. This will vary with the nature of the load. * To restart the SA07 remove the fault and recycle VCC or, alternatively, toggle the I LIMIT/SHDN (pin16) with a shut down pulse.
CONTACTINGCIRRUSLOGICSUPPORT
For all Apex Precision Power product questions and inquiries, call toll free 800-546-2739 in North America. For inquiries via email, please contact tucson.support@cirrus.com. International customers can also request support by contacting their local Cirrus Logic Sales Representative. To find the one nearest to you, go to www.cirrus.com
IMPORTANTNOTICE Cirrus Logic, Inc. and its subsidiaries ("Cirrus") believe that the information contained in this document is accurate and reliable. However, the information is subject to change without notice and is provided "AS IS" without warranty of any kind (express or implied). Customers are advised to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, indemnification, and limitation of liability. No responsibility is assumed by Cirrus for the use of this information, including use of this information as the basis for manufacture or sale of any items, or for infringement of patents or other rights of third parties. This document is the property of Cirrus and by furnishing this information, Cirrus grants no license, express or implied under any patents, mask work rights, copyrights, trademarks, trade secrets or other intellectual property rights. Cirrus owns the copyrights associated with the information contained herein and gives consent for copies to be made of the information only for use within your organization with respect to Cirrus integrated circuits or other products of Cirrus. This consent does not extend to other copying such as copying for general distribution, advertising or promotional purposes, or for creating any work for resale. CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE ("CRITICAL APPLICATIONS"). CIRRUS PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED TO BE SUITABLE FOR USE IN PRODUCTS SURGICALLY IMPLANTED INTO THE BODY, AUTOMOTIVE SAFETY OR SECURITY DEVICES, LIFE SUPPORT PRODUCTS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF CIRRUS PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER'S RISK AND CIRRUS DISCLAIMS AND MAKES NO WARRANTY, EXPRESS, STATUTORY OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE, WITH REGARD TO ANY CIRRUS PRODUCT THAT IS USED IN SUCH A MANNER. IF THE CUSTOMER OR CUSTOMER'S CUSTOMER USES OR PERMITS THE USE OF CIRRUS PRODUCTS IN CRITICAL APPLICATIONS, CUSTOMER AGREES, BY SUCH USE, TO FULLY INDEMNIFY CIRRUS, ITS OFFICERS, DIRECTORS, EMPLOYEES, DISTRIBUTORS AND OTHER AGENTS FROM ANY AND ALL LIABILITY, INCLUDING ATTORNEYS' FEES AND COSTS, THAT MAY RESULT FROM OR ARISE IN CONNECTION WITH THESE USES. Cirrus Logic, Cirrus, and the Cirrus Logic logo designs, Apex and Apex Precision Power are trademarks of Cirrus Logic, Inc. All other brand and product names in this document may be trademarks or service marks of their respective owners.
SA07U

7

▲Up To Search▲

Price & Availability of SA07

	To Download SA07 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .